User:TheAnarcat: Difference between revisions

From Amateur Radio Wiki
Jump to navigation Jump to search
Line 31: Line 31:
|+
|+
! Part              || Amount || Where || Price || Notes
! Part              || Amount || Where || Price || Notes
|+
!colspan="5"|Parts on hand
|-
| tripod            || 1    || addison (done)    || 40$ || ~2' x 2'
|-
| 3m steel pole      || 1    || downstairs || 0$? || to connect the beam and tripod, 1¼"
|-
| sandbags          || 3    || home depot (done) || 30$? || one per leg
|+
!colspan="5"|Parts missing
|-
|-
| AUG 12 copper wire || 44.4m  || ???  || 29.32$ (addison?) 48.64$ pour 2x12 22m (dubo) || addison doesn't have bare wire, and [http://www.dubo.qc.ca/ dubo] only has bare up to 8 gage, too big (it's mainly for grounds)
| AUG 12 copper wire || 44.4m  || ???  || 29.32$ (addison?) 48.64$ pour 2x12 22m (dubo) || addison doesn't have bare wire, and [http://www.dubo.qc.ca/ dubo] only has bare up to 8 gage, too big (it's mainly for grounds)
|-
| tripod            || 1    || addison (done)    || 40$ || ~2' x 2'
|-
|-
| hose clamps        || 8    || home depot || ~15$ || unit price ~2$
| hose clamps        || 8    || home depot || ~15$ || unit price ~2$
Line 43: Line 51:
|-
|-
| U clamps and bolts || 4    || home depot || ? || for the beam/pole fitting
| U clamps and bolts || 4    || home depot || ? || for the beam/pole fitting
|-
| sandbags          || 3    || home depot (done) || 30$? || one per leg
|-
|-
| <s>8m ½"PVC</s>          || 4    || home depot || ? || PVC pipes are too flexible to hold properly, we need fiberglass
| <s>8m ½"PVC</s>          || 4    || home depot || ? || PVC pipes are too flexible to hold properly, we need fiberglass
Line 51: Line 57:
|-
|-
| plywood            || 6'x5' || home depot || 5$? || 1' x 2' used for the beam/pole fitting
| plywood            || 6'x5' || home depot || 5$? || 1' x 2' used for the beam/pole fitting
|-
| 3m steel pole      || 1    || downstairs || 0$? || to connect the beam and tripod, 1¼"
|+
|+
!colspan="5"|Phase II
!colspan="5"|Phase II

Revision as of 12:41, 7 May 2011

I am anarcat and i hope i'm not screwing things up here too much. :)

I just passed my basic qualitification in Canada, with honors (so I can operate HF), yay! I am now AKA VA2ANK. -- TheAnarcat 21:50, 10 October 2010 (CDT)

My rig

I uploaded a few photos in this album.

New quad antenna project

A sketch of my antenna

I am working on building a new antenna, pictured right. It is based on this design, which uses a mix of PVC pipes and fiberglass rods, except I adapt it to a 20m antenna.

Here's my parts list.

Part Amount Where Price Notes
Parts on hand
tripod 1 addison (done) 40$ ~2' x 2'
3m steel pole 1 downstairs 0$? to connect the beam and tripod, 1¼"
sandbags 3 home depot (done) 30$? one per leg
Parts missing
AUG 12 copper wire 44.4m ??? 29.32$ (addison?) 48.64$ pour 2x12 22m (dubo) addison doesn't have bare wire, and dubo only has bare up to 8 gage, too big (it's mainly for grounds)
hose clamps 8 home depot ~15$ unit price ~2$
1"x½" copper pipe 8 home depot ~5$ we'll use tie-wraps instead for spreader/wire attachment
8"x½" plastic tube 1 home depot (done) ~2$ for spreader/wire attachment
U clamps and bolts 4 home depot ? for the beam/pole fitting
8m ½"PVC 4 home depot ? PVC pipes are too flexible to hold properly, we need fiberglass
4m 1"PVC 1 home depot ? 1" en stock
plywood 6'x5' home depot 5$? 1' x 2' used for the beam/pole fitting
Phase II
5-way 1"PVC conn. 2 creativeshelters.com 3.08$
15' 1" fiberglass 8 mgs4u.com ~160$ unit price 17.10$ - use the type 1L because the type 1 doesn't fit in the 5-way PVC connector

Total price: ~280$

Références

Je collecte ici des bons sites au sujet du ham radio.

Software

This needs to be merged into Software 

  xplanet -latitude 45.5 -longitude -73.66 -wait 60 -label -projection azimuthal -fork -radius 90

  ibp FN35EM

... others to follow, there's a whole hamradio section in debian.

Stuff to buy next

Retrieved from "http://wiki.hamtools.org/index.php?title=User:TheAnarcat&oldid=4899"