Repeater
In amateur and commercial land-mobile radio, as well as in radio/television broadcasting, a repeater is a station which receives a signal on one frequency, immediately retransmitting it (normally on a different frequency) in order to extend the original signal's coverage area.
These stations may occasionally be called "relay" transmitters; broadcast-band stations may also use terms such as "rebroadcaster" or "broadcast translator". On communications satellites, each individual receiver/transmitter pair is known as a "transponder". In all cases, the principle is the same. A signal is received, amplified and retransmitted.
VHF and UHF radio
Many amateurs access 2 metres and higher bands using small mobile transmitters or hand-held devices; available power is by necessity limited in battery operation while antenna height and size are also constrained to maintain portability. Moving vehicles typically use small omnidirectional vertical antennas. Signals are often weak and the available line of sight distance from a ground-based mobile station is severely limited.
Even in fixed operation where an originating station's power and antenna could be easily upgraded, propagation at VHF or higher frequencies remains primarily line-of-sight with a very limited amount of diffraction at points where a signal encounters terrestrial obstacles. This limitation becomes more pronounced as frequency increases, effectively imposing a maximum distance for any signal to be received directly. Often a weak, distant signal which is received clearly atop a hill or mountain may be unintelligible at the same distance in valleys or behind obstacles such as mountains or skyscrapers.
A repeater can be situated atop a terrestrial obstacle or a tall structure, providing clear line of sight to multiple users on the ground which cannot directly see each other but who can all obtain a clear path to a carefully-located repeater/relay station. As most repeaters deployed by local amateur radio clubs are fixed stations, their signals are powerful and can be heard for a greater distance. A fixed repeater site may also be a suitable location to deploy gateway facilities for over-the-air access to services such as IRLP, Echolink or land line phone patches.
Operation and procedure
In amateur radio, repeater frequencies are normally 29.5MHz or higher, with 2 metres and 70 centimetres among the most popular bands. On 2 metres VHF, a repeater's input frequency is typically separated from the retransmitted output by 600kHz to prevent the transmitter from interfering with the original received signal. Wider offsets would be used on higher frequency bands.
A repeater is normally an automated, unattended station. A control operator must for legal reasons be capable both of monitoring the retransmitted signals and remotely silencing the transmitter should problems occur, but all routine tasks such as periodic station identification are normally handled by an automated controller board.
The transmitter is only activated when a signal is present at the input; some repeaters may also require specific tones be present on the input signal. A timer is also provided to stop the repeater if more than three minutes pass without any break in transmission, so that a fault condition does not leave the transmitter continuously on. An error message (TO: - --- via CW or "timeout" via voice) is transmitted in this case.
Operating procedure on repeater stations differs slightly from direct communication, in that the repeater is on a fixed frequency monitored or actively used by many local amateurs. The transmission of repeated "CQ CQ CQ DE <callsign>" is typical on HF, where hams must slowly and manually tune across the various bands to find the calling station, but is pointless on a fixed-frequency repeater. When other amateurs are already monitoring the repeater frequency, sending just a callsign or a callsign followed by the word "monitoring" normally gets a response with no need for "CQ" or repetition.
Digital repeaters
Digital data signals may be retransmitted using a store-and-forward approach, where a station receives a packet of data and stores it for nearly-immediate retransmission. For instance, APRS uses a single frequency (144.39 or 144.8 MHz, depending on region) with multiple stations on the same frequency.
See also
| Radio apparatus | |
| Apparatus | Keys - Morse * Kits * Radio/PC Interfaces * Receivers and transceivers * Software Defined Radio (SDR) * Vintage Radio |
| Manufacturers | Alinco * Elecraft * Flex Radio Systems * MFJ * Icom * Kenwood * RF-Space * Ten Tec * Yaesu |
| Transceivers | Alinco DX-70TH * Elecraft K1 * Elecraft K2 * Hendricks QRP Kits * Icom * Kenwood * Yaesu |
| Projects | Build a simple 160 metre receiver * Powering a hand held transceiver from an AC power supply |
| See also | Antennas |