Operating procedures

Use this page to explain what various functions of a transceiver are and how to use them.

Buttons and knobs

A ham radio has usually zillions of buttons and knobs and dials on its front panel. To the neophyte, those just look very confusing and unhelpful. This aims to clarify this jargon for you.

AF gain

"Audio Frequency Gain". Simply the volume control - like the one at your everyday BC radio.

RF gain

Controls the amount of pre-amplification in the RX before the first if stage is reached. In some radios, if this is zero, almost no signal will reach the speakers and you will not able to hear anything. The idea here is that the signals you receive on your antenna can be very weak and must be hugely amplified to hear far away stations.

It is very useful in QRN (natural interference) and other noisy conditions where otherwise SSB stations become unreadable. Take the RF gain back and have a QSO (conversation) that would be impossible with full gain.

Some rigs have also a switchable additional RF gain button, that sometimes has also an attenuation function. This in effect just widens the margin of the overall RF gain.

Squelch

Squelch is used to silence the loudspeaker when no signal is present the frequency of operation. In ham radio this will suppress the general static that remains present on most bands and is heard during breaks in the distant station's transmission. Squelch will not remove noise received simultaneously with valid signal; that may only be done with directional antennas (to block interference from other directions) or filters (to block specific frequencies).

At its most basic level, squelch opens the loudspeaker when any signal is present. Another one of the several forms of squelch used in ham radios, CTCSS, requires that a specific tone be present in a received signal - reducing the probability of a repeater system being triggered by random noise, by adjacent-channel interference or by co-channel interference from DX stations intending to access another repeater on the same frequency in another city.

Passband Tuning

Passband tuning manipulates the tuning circuitry of the transceiver, allowing "close together" signals to be separated - one is rejected by the filter, one is allowed to pass through. It is similar to IF shift, where the IF of the transceiver is shifted slightly to tune in slightly off frequency signals.

Passband tuning and IF shift are used because simply narrowing down the passband would produce muffling of any audio signals. Narrowing down the passband is however the best way to pick out narrow band signals (like CW and narrow band digimodes) from a noisy band.

External link from QST

RIT

RIT : Receiver Incremental Tuning, Receive Independant of Transmit is the ability to shift the receive frequency of a transceiver away from the transmit frequency by a small amount. Used in SSB transmissions, it was very useful in older rigs that had frequency stability problems. RIT can also be used to deliberately transmit and receive on different fequencies. This is known as "working split", with the difference in frequencies usually 3khz to 10Khz.

Roofing Filters

A roofing filter is used in an HF receiver and us usually found after the first receiver mixer. It's purpose is to reduce the passband of the first IF (first intermediate frequency) to between 6kHz and 20KHz. This in turn reduces distortion in any amplifier and mixer circuits.

Roofing filters are usually usually crystal types because of the steeper filtering curve that they produce.

Roofing filters can be much narrower than 20kHz when listening to very weak CW signals. In this case the filter may have a bandpass of as low as 250Hz. This also requires that the first IF in the receiver is below VHF, perhaps as low as 9MHz.

See the regular Wikipedia

XIT

Similar to RIT above, but the transmit frequency is changed while the receive frequency is that shown on the frequency display.

On the air procedures

Once you have tuned your station, you can start trying to make contact, that is transmitting.

Before making your first contact

This will be routine to regular ham operators, but it should prove useful for newcomers.

1. Study the band plans and propagation conditions again that allow you (or not) to operate on which frequencies.
2. Review the jargon (e.g. Q signals and phonetic alphabet) to understand what can be said or how to say it!

Making contact

Here's a quick reminder of the basic steps to take to make contact:

1. Tune your station to that frequency. That may mean adjusting your antenna switcher/tuner, tuning your radio to the desired frequency, etc. See above.
2. Listen for a little to see if the frequency is in use.
3. Start transmitting

Those procedures are the basics. "Transmitting" can vary a lot according to what band you're on, so we have detailed explicit procedures for those two broad categories.

Channelized (VHF/UHF) operation

1. Tune your radio to the channel you agreed on
2. Turn off the offset (unless you are operating on a repeater for which specific procedures exist)
3. Listen to see if the frequency is in use
4. Key the microphone and announce your call sign and the callsign of the person you're trying to reach:

VA2HGQ this is VA2ANK

1. The receiving party would answer:

VA2ANK, VA2HGQ

Congratulations, you have made contact! You can now talk on the channel, according to local regulations of course. For example, Canadian regulations require you to announce your call sign every thirty minutes and at the beginning and end of every contact.

If you can't make contact, you can wait on the channel and announce it as such:

VA2ANK is monitoring

... or listening.

Once you are done, you can wrap up with this:

Okay hugo, talk to you later. VA2HGQ, VA2ANK clear.

HF operation

While VHF and UHF have the luxury of channelized operation and repeaters, the HF band is much wilder: you will need much more practice to tune your receiver to understand the other correctly. So while HF give you much longer range (worldwide instead of citywide), it comes at the price of convenience. But you gain incredible freedom and power.

Here, you are not limited to specific channels and can tune your frequency on the kilohertz, depending on the radio capabilities of course.

Interference is common: natural, man-made are the usual occurrence, and in fact an interfering station may not even be able to hear you sometimes.

We distinguish between two main modes on HF: phone or cw modes.

"Phone" or voice operations

Phone operations can happen on any band but 30 meters in most places, but you should be careful to respect the informal agreements of band allocations. See the bands page for more information there. For popular DX frequencies, you should look into 3.775 to 3.800MHz, 7.075 to 7.100 Mhz and 14.175 to 14.225Mhz.

1. Tune your radio to the desired frequency
2. Listen in on the frequency before transmitting
3. Ask if the frequency is in use, by saying:

Is this frequency in use VA2ANK

1. If the frequency is not in use, make a CQ call:

CQ CQ CQ This is VA2ANK VA2ANK VA2ANK over

1. If you are heard, your contact may respond with:

VA2ANK this is VA2HGQ VA2HGQ VA2HGQ over

1. If you hear that, you can start your conversation, usually with technical details about the quality of the signal, your location, the weather, etc

VA2HGQ this is VA2ANK thanks for the call. You are 59 here in Montreal and it's a beautiful sunny day outside. The name is Antoine, how do you copy? VA2HGQ this is VA2ANK. Over.

Then you can have your conversation. If the contact is barely audible, you should fall back on the use of phonetics. Example:

VA2HGQ, this is Victor Alpha Two Alpha November Kilo, I say again Victor Alpha Two Alpha November Kilo. Name here is Antoine, I spell Alpha November Tango Oscar India November Echo. So how do you copy? Back to you. VA2HGQ this is VA2ANK. Over.

Reminders:

1. LSB on 160, 80 and 40m bands
2. USB on 20, 15 and 10m bands
3. No phone on 30m (because of the 1Khz bandwidth limit)

See also

• Apparatus

Operating procedures
Operation	Callsigns and ITU prefixes * Codes and Alphabets * Modes * Morse code * Nets * UK licensing * Terminology
DX and Contesting	Awards and Certificates * DXCC * DX cluster * Field day * Gridsquares * Logging * QSL and QSL Bureaus * Records - Distance
Emergencies	Emergency Frequencies * ARES * IRESC * SATERN * Weather spotting
QRP	Trail-Friendly Radio
Utilities	Beacons (/B) and Time Beacons